Dies built by long-standing partners
Tool design and manufacture is handled through third-party specialists we have worked alongside for over 25 years. We hold the specification, cost and lead time.
Injection moulding · Precast accessories · Middle East
We hold the cover.To the millimetre.
Cochin Plastic Industries moulds the spacers, caps and pads that keep reinforcement exactly where the drawing says it should be — supplied to precast plants and contractors across the region from Salmabad, Bahrain.
30+ yearsManufacturing for the precast industry
ISO 45001Certified health and safety management
25+ yearsWorking with the same tooling partners
Section detail — wheel spacer
Cover 25 mm
What we do
Capability
One point of contact, from the die to the delivery note.
We mould in-house and manage everything around it — including the tooling, which is produced by specialist partners we have worked with for more than 25 years. You deal with us, not with three suppliers.
Polymer specified to the job
Grade, colour and additive package chosen for load, UV exposure and site conditions, including customer-nominated compounds.
Moulding at production volume
High-volume runs with consistent shot weights and dimensions, plus partial or full outsourced manufacturing for other producers.
Product range
Standard range
Accessories for the precast bed.
Everything below is moulded to hold position under vibration, pouring and handling — and to come off the bed cleanly.
Wheel spacers
The workhorse. Clips onto the bar and rolls into place, holding cover on vertical and horizontal faces.
- Type
- Clip-on wheel
- Cover
- To specification
- Bar Ø
- To specification
Large-diameter wheels
Heavier sections and deep cover, moulded with a reinforced spoke pattern to carry the load without deflecting.
- Type
- Clip-on wheel
- Cover
- Deep cover
- Sizes
- Made to order
Clip spacers
Snap-fit onto a single bar and stand on splayed feet against the mould face. Fast to fit by hand along a long run of steel.
- Type
- Single-bar clip
- Cover
- To specification
- Bar Ø
- To specification
Praxifix
A four-leg spacer with a wide, stable footprint for mesh and slab reinforcement that has to stay put during the pour.
- Type
- Four-leg base
- Use
- Slabs and mesh
- Heights
- Multiple sizes
Hollow core caps
Plug the voids in hollow core slabs before grouting, keeping the core clean and the fill where it belongs.
- Type
- Void plug
- Fit
- Matched to core
- Sizes
- Made to order
Shim pads
Stackable levelling pads for setting and packing precast units to line and level during erection.
- Type
- Stackable shim
- Thickness
- Range to order
- Use
- Levelling and packing
Rebar caps
Mushroom-head caps for exposed starter bars, so protruding steel is covered and visible on site.
- Type
- Protective cap
- Bar Ø
- To specification
- Colour
- High-visibility
And the rest of the bed
The range extends beyond this page — lifting accessories, cones, plugs, formwork consumables and parts we already mould for other precast plants. Tell us the part and we'll tell you whether we make it or can tool for it.
Ask about a partBeyond the catalogue
Custom manufacturing
Bring us the part, or bring us the volume.
For high-volume industries we take on the pieces of manufacturing that are slowing you down — a tool, a material change, a production line, or the whole thing.
Die and tool development
From a drawing, a 3D file or a sample part, we develop the die with our tooling partners and prove it out before committing to production.
Raw material customisation
Polymer grade, colour, filler and additive package specified around how and where the part has to perform — including compounds you nominate.
Contract manufacturing
Take on a single moulded component or an entire product line, in partial or full capacity, packed and labelled under your brand.
How we work
From enquiry to delivery
Four steps, in order.
Specification
Send a drawing, a sample or a description. We confirm dimensions, cover, bar size, material and volume.
Tooling
For a new part, the die is produced by our long-term tooling partners. We manage the design, cost and lead time on your behalf.
Sampling
First-off samples go to you for fit and approval on your own bed, before the production run is released.
Production
Approved parts move to scheduled runs, packed and labelled for your plant, with repeat orders held to the same tool.
The company
About us
Thirty years of moulding for the casting bed.
Cochin Plastic Industries W.L.L. is an injection moulding manufacturer in Salmabad, Bahrain, supplying the precast concrete industry across the Middle East for more than 30 years.
We make the small parts the finished panel depends on: the spacers that set cover, the caps that close a core, the pads that bring a unit to level. Three decades in, the business runs on relationships as much as machines — our tooling partners have been working with us for over 25 years, which is why a die change is a conversation rather than a procurement exercise.
The company is certified to ISO 45001 for occupational health and safety management. Alongside our own range, we manufacture to order for companies who need parts moulded at volume, under their drawing, their material specification and their brand.
- What we makePrecast accessories, plus custom moulded components for high-volume industries
- How we make itInjection moulding in-house; tooling through long-standing specialist partners
- Who we supplyPrecast plants, concrete product manufacturers, contractors and trade distributors
- Where we areSalmabad, Kingdom of Bahrain — supplying the region, export enquiries welcome
- CertificationISO 45001 occupational health and safety management
Contact
Tell us what you need moulded.
Send a drawing, a sample photo or just the part name and quantity. We'll come back with availability, tooling requirements and a price.
- Company
- Cochin Plastic Industries W.L.L.
- Address
- Building 382, Road 1205, Block 712
Salmabad, Kingdom of Bahrain - Telephone
- +973 7790 3113
- info@cochinplastics.com
- Working hours
- Saturday – Thursday, 8:00 am – 5:00 pm
- Certification
- ISO 45001